• ARIS Klappenversteller Ex-Zonen

Linea­ris CL Ex 1

Elec­tro-mecha­ni­cal dam­per actua­tor for Ex-Zone 1

The CL series offers clas­sic dri­ve tech­no­lo­gy with motor/gear com­bi­na­ti­on and cam mecha­nism in a clas­sic design. Three series up to 300 Nm in com­bi­na­ti­on with various actua­ting times open up a wide ran­ge of app­li­ca­ti­ons for a wide varie­ty of indus­tri­al tasks. Of cour­se, the CL series offers not only a robust metal hou­sing, but also all com­mer­ci­al­ly avail­ab­le opti­ons, from the addi­tio­nal limit switch to the posi­tio­ner with load cut-off. Three cable ent­ries M20 x 1.5 allow easy wiring even in the case of high-cross-sec­tion leads. The CL series is also avail­ab­le in vol­ta­ges of 230 V, 115 V, 24 V AC or 24 V DC.

A stain­less steel split spind­le with a dry­s­pin® spind­le nut ensu­res relia­ble and main­ten­an­ce-free ope­ra­ti­on. Due to the high gra­di­ent, the requi­red engi­ne speed is signi­fi­cant­ly redu­ced in com­pa­ri­son to the clas­sic design, so that the engi­nes run much smoot­her and quie­ter. This con­s­i­der­ab­ly increa­ses the ser­vice life of the motors. Ins­te­ad of the com­mer­ci­al­ly avail­ab­le cas­tings, Linea­ris CL uses anodi­sed alu­mi­num machined parts, which are signi­fi­cant­ly more robust at low weight. The Linea­ris has been deve­lo­ped by prac­titio­ners. Long holes in the bra­ckets allow easy assem­bly even by only one mecha­nic. Dirt depo­sits are pre­ven­ted by the spind­le in the dry run so that lar­ge and expen­si­ve bel­lows designs are no lon­ger requi­red. The syn­chro­nous motors used in the dri­ve head ope­ra­te with a pure­ly fre­quen­cy-depen­dent posi­tio­n­ing time and thus ensu­re pre­cise con­trol. A robust powder-coated hou­sing relia­b­ly pro­tects dri­ve tech­no­lo­gy even in harsh indus­tri­al envi­ron­ments. Despi­te the com­pact dimen­si­ons of the dri­ve head, the Linea­ris CL allows all stan­dard opti­ons, inclu­ding emer­gen­cy ope­ra­ti­on in case of power fail­u­re.

The Linea­ris lift unit is also desi­gned to meet the requi­re­ments of the ATEX direc­tives so that the com­bi­na­ti­on of the line­ar unit and the zone 1 dri­ve is a relia­ble unit.

The Linea­ris CL is avail­ab­le in stan­dard stro­ke lengths of 150 and 300 mm for actua­tors up to 5000 N.

Other stro­ke lengths are also avail­ab­le on request.

Force

6005000

N

Actua­ting time

0.78.5

mm/s

SARI Gasklappe Industriearmaturen
Messingventil RV
Messingventil RV
ARIS Regelventil
ARIS Regelventil
ARIS Regelventil
ARIS Ringdrosselklappe Industriearmaturen
ARIS Mischarmatur
Messingkugelhahn
ARIS Kugelhahn
ARIS Kugelhahn
ARIS Kugelhahn
ARIS Kugelhahn

Order right away…

Sin­gle com­po­nent or com­ple­te unit.

  • Dri­ve

    • CL dri­ve head
      • Robust indus­tri­al design
      • Install­ab­le in any posi­ti­on
      • Main­ten­an­ce free
      • Short-cir­cuit pro­of syn­chro­nous motor
      • Pre­cise­ly adjus­ta­ble swit­ching cams
      • Nume­rous opti­ons, e.g. addi­tio­nal swit­ches, poten­tio­me­ter, posi­ti­on indi­ca­tor, posi­ti­on con­trol­ler, manu­al over­ri­de etc.
      • Con­trol­ler card PMR-Nano optio­nal
      • Cover 98–178 mm, depen­ding on opti­ons
      • Con­trol­ler card PMR-CL optio­nal
  • Linear­ein­heit

    Fea­tures

    • Stain­less steel high-helix lead screw Ø18
    • Lead 40 mm with opti­mi­zed effi­ci­en­cy
    • Less turns per stro­ke length
    • Long-life motor
    • Slow and smooth motor move­ment
    • Low noi­se and vibra­ti­on
    • Hol­ding tor­que by self-hold of the actua­tor
    • Sepa­r­a­te­ly exch­an­ge­ab­le actua­tor
    • High-strength, anodi­zed alu­mi­num mil­led parts, cor­ro­si­on resistant and light­weight
    • Long holes for fas­ten­ing, i.e. easy instal­la­ti­on
    • Main­ten­an­ce-free by dry-run, no lub­ri­ca­ti­on necessa­ry, no dirt depo­sits on grea­se (lon­ger life span)
    • Embed­ded (dry) lub­ri­cants insi­de the lead screw nut
    • High qua­li­ty „dry­s­pin® tech­no­lo­gy“. Lead screw and nut made by igus©
  • dry­s­pin® tech­no­lo­gy

    High-helix: Hig­her life span and effi­ci­en­cy

    The dry­s­pin® tech­no­lo­gy is based on wear-resi­si­stant igus® high per­for­mance poly­mers, spe­ci­al­ly desi­gned for screw dri­ves, dry­s­pin® offers a hig­her life span and effi cien­cy to high-heli­xes by their cha­rac­te­ris­tics and geo­me­tries, spe­ci­al­ly matched to the nut and lead screw. By their free­dom from lub­ri­ca­ti­on, dry­s­pin® screw dri­ves are sui­ta­ble for usa­ge in rough indus­tri­al just as in clean and hygie­nic envi­ron­ments (e.g. labo­ra­to­ry auto­ma­ti­on).

    Spind­le nut

    • Lub­ri­cant-free
    • High-tech poly­mer igli­dur® J insi­de alu­mi­num block
    • Opti­mal trans­mis­si­on of the tor­que by form clo­sure
    • Vibra­ti­on-iso­la­ting
    • Smooth and ste­ady run
1
2
3
4
Linearis Ex-Zonen Linearantriebe als Klappenversteller für Ex-Zone 1
1

CL dri­ve head

Atex Zone 1

2

Linea­ris lift unit

ATEX type

3

Dry­S­pin thread tech­no­lo­gy

4

Robust indus­tri­al design

Spe­ci­fi­ca­ti­ons dam­per actua­tor Linea­ris CL Ex 1
Linea­ris CL Ex 1
Forcemax. 5000 N (hig­her forces upon request)
Tra­vel time0.7 mm…8.5 mm/s (load inde­pen­dant at AC)
Tra­vel150/300 mm Hub (more stro­ke lengths upon request)
Power sup­ply230 V AC, 50/60 Hz
(optio­nal 24/115 V AC, 400 V DS, 12/24 V DC)
Ambi­ent tem­pe­ra­tu­re–15 °C…+60 °C
Pro­tec­tion classIP 65
Duty cycle 100%
LABS free accord­ing to Daim­ler test stan­dard appro­ved by Fraun­ho­fer Insti­tu­te.