PD/PE

Pneu­ma­tic actua­tors

The ARIS pneu­ma­tic part-turn actua­tors pro­vi­de a uni­form tor­que in a sleek case that is used both for the dou­ble and sin­gle acting. The pneu­ma­tic actua­tors are avail­ab­le with a varie­ty of access­ories and various opti­ons. We sup­ply the dri­ves indi­vi­dual­ly or direct­ly on a ful­ly assem­bled fit­ting.

PD/PE actua­tors (type 15 and hig­her) fea­ture a bi-direc­tio­nal tra­vel stop which allow a ±10° adjust­ment in both clo­sing and ope­ning direc­tions. This gua­ran­tees a ran­ge of adjust­ment bet­ween 70° and 110° of actua­tor stro­ke. Tra­vel stops are desi­gned to absorb the maxi­mum rated tor­que of the actua­tor and the maxi­mum impact load asso­cia­ted with recom­men­ded speed stro­ke.

To increa­se pis­ton resis­tan­ce both tra­vel stops arrest the pis­tons in their part with the lar­gest mass of mate­ri­al. Adjust­ment of the CCW and CW rota­ti­on is effec­ted by tur­ning the respec­tive left (MAX) and right stop (0°) adjust­ment screws.

Tor­que

55000

Nm

Swi­vel ran­ge

70110

Grad

SARI Gasklappe Industriearmaturen
Messingventil RV
Messingventil RV
ARIS Regelventil
ARIS Regelventil
ARIS Regelventil
ARIS Ringdrosselklappe Industriearmaturen
ARIS Mischarmatur
Messingkugelhahn
ARIS Kugelhahn
ARIS Kugelhahn
ARIS Kugelhahn
ARIS Kugelhahn

Order right away…

Sin­gle com­po­nent or com­ple­te unit.

  • Cha­rac­te­ris­tics

    PD/PE

    • Hou­sing anodi­zed alu­mi­num
    • Con­nec­tions acc. DIN/ISO/NAMUR
    • Sett­able tra­vel stops
    • Pre-stres­sed pro­tec­ted springs
    • Posi­ti­on indi­ca­tor
    • SIL2 appro­ved
  • Fea­tures

    Sin­gle and dou­ble-acting pneu­ma­tic actua­tors

    • Namur VDI/VDE 3845 and ISO 5211 con­nec­tions on all sizes. No spe­cial blocks are requi­red to mount sole­no­id val­ves, limit swit­ches or posi­tio­ners.

    • The stan­dard ang­le of rota­ti­on is 90Åã. Addi­tio­nal tra­vel rota­ti­ons of 120°, 135°, 150° and 180° are avail­ab­le. PD/PE 15 and upper sizes fea­ture a tra­vel stop wit ±10° in both open and clo­se direc­tions. Other angles (e.g. 30°) are optio­nal.

    • The fema­le pini­on dri­ve is stan­dard with a dou­ble squa­re out­put dri­ve, and optio­nal with a dou­ble-D dri­ve, key­ed dri­ve and designs to meet your spe­ci­fic requi­re­ments.

    • Shaft bea­rings iso­la­te the pini­on gear from the hou­sing and sup­port the shaft for high cycle app­li­ca­ti­ons.

    • Ambi­ent tem­pe­ra­tu­re: -20 °C to +80 °C (optio­nal -40 °C to +150 °C).

    • The pini­on teeth are enga­ged for the full length and stro­ke of the pis­ton.

    • The pini­on height allows manu­al over­ri­de without dis­tur­bing the indi­ca­ted posi­ti­ons.

    • Exter­nal open/close indi­ca­tor is stan­dard, avail­ab­le indi­ca­tors for all rota­ti­ons.

    • Pis­tons incorpo­ra­te dou­ble wear pads to sepa­ra­te the rack from the actua­tor wall and ser­ve as both gui­de and wear bea­rings.

    • PD/PE series pis­tons fea­ture a key­way as anti-blo­wout sys­tem.

    • All inter­nal and exter­nal com­pon­ents are trea­ted to increa­se cor­ro­si­on resis­tan­ce.

    • Epo­xy coated spe­cial steel springs are pre-loa­ded.

    • The stain­less steel end cap fas­te­ners are extra long to allow for spring rela­xa­ti­on (PE only).

    • Air pres­su­re ope­ra­ti­on from 2 to 10 bar (40–150 PSI). Water, nitro­gen and com­pa­ti­ble hydrau­lic flu­ids may also be used to power the actua­tor.

    • All exter­nal fas­te­ners are cor­ro­si­on resistant stain­less steel.

    • All units are per­man­ent­ly lub­ri­ca­ted at the fac­to­ry with non-sili­co­ne grea­se.

    • All units are extern­al­ly stam­ped with a pro­gres­si­ve trace­ab­le seri­al num­ber.

    • 100% of all units are fac­to­ry pres­su­re leak tested.

1
2
3
4
Pneumatikantrieb PD/PE Pneumatische Stellantriebe Pneumatikantriebe
1

Schlag­fes­te Hau­be

2

Gehäu­se Alu-Druck­guss

3

Diver­se Boh­run­gen

4

Wel­le in Wunsch­form

Spe­ci­fi­ca­ti­ons PD/PE pneu­ma­tic actua­tor
PD/PE
Pini­onElec­tro­less nickel coated car­bon steel (stain­less steel optio­nal), blow-out pro­of
Posi­ti­on indi­ca­torTech­no­po­ly­mer hou­sing
Pis­tonAnodi­zed or powder-coated
End capsEpo­xy powder-coated
Bea­ring padsTech­no­po­ly­mer, lar­ge con­tact area, long life resis­tan­ce.
Hou­singExtru­ded alu­mi­num hou­sing
SealingsTem­pe­ra­tu­re ran­ge from -20 °C to +80 °C (-10 °F to +176 °F)
with stan­dard Buna-N seals. Hig­her tem­pe­ra­tu­re with optio­nal
Viton seals and tech­no­po­ly­mer pis­ton gui­des and bea­rings:
120 °C (250 °F) con­ti­nuous and 150 °C (300 °F) cyclic. Lower
tem­pe­ra­tures with sili­co­ne seals: -50 °C (-55 °F).